Installing Your Own Water Heater

Your next-door neighbor was up all evening handling a broken water heater and also you simply invested the last half hr paying attention to him complaining. He had corroded water pouring out of the ceiling, due to the fact that the water heater was up in the attic above the master bedroom. The emergency drainpipe pan that was meant to catch all the water from the dripping water heater was connected up with insulation that had fallen under the frying pan over the years. His bedroom is swamped. His bed is wet. The ceiling is dropping. He is worn out as well as grouchy from being up all night.

You reach assuming that you sure are glad it has actually not happened to you. You are wise enough to understand at this moment that all your houses in your area were developed at the same time. Your hot water heater is currently about twelve years of age as well as you declare that your hot water heater is surviving on obtained time. You heard how much trouble your neighbor experienced last night. His plumbing bill was pretty high because the plumbing had to go out in the middle of the evening, yet that is the least of his problems. His bed is messed up, as well as the carpeting as well as the ceiling also.

You understand some standard plumbing essentials and you have a pal that knows a little about plumbing, so you hire your close friend and are determined to tackle this job over the weekend break. It is good that you have a good friend to assist because your hot water heater is in the attic, like your next-door neighbors.

The standard steps to install water heater on your own are as complies with:

Step 1. You go up into the attic room and also devise your method for lowering and also elevating the containers. The container is hefty, so you will most likely wish to have some really strong rope so that you can decrease the old water heater down and also elevate the new one up.

Action 2. Turn off the gas likely to the hot water heater at the shutoff that links to the front of the hot water heater. Detach the gas line from the hot water heater.

Action 3. Turn off the water to the hot water heater or if the valve is not functioning switch off the water to your house. If the valve is not functioning it will need to be changed. In a future write-up, we will certainly go over exactly how to change your shutoff.

Step 4. Detach the water lines likely to the container. The water lines are commonly flexible lines that have a nut that you can transform counterclockwise to eliminate.

Tip 5. Disconnect the air vent pipeline from the top of the tank.

Step 6. Drain pipes the hot water heater by connecting a water pipe to the drain pipe connection at the end of the water heater.

Action 7. Lower the old water heater down the attic stairs using your really strong rope and your extremely solid as well as well collaborated buddies assist. This is most likely one of the most harmful parts of the entire project. Please beware not to hurt any individual, including on your own.

Step 8. Increase your new storage tank into the attic room similarly, you obtained the old one out.

Tip 9. Put the brand-new hot water heater into the drain pan, ensuring to clean the frying pan and inspect for openings in the pan first.

Step 10. Reconnect the water lines as well as gas lines and vent similarly you took them apart.

Action 11. Your hot water heater is currently mounted as well as you are ready to turn on the water. Have your friend stay in the attic room to watch for leakages while you turn the water on very gradually. Check out each connection that you made and check for leakages. If you spot a leakage make sure to tighten it up. Do not tighten it up so hard that it damages a suitable. Switch on the water on the warm side at a tub spout and bleed all the air out of the hot water heater as well as water lines. Run the water in the bathtub till water comes out clean as well as clear without any air ruptures.

Step 12. Turn on the gas at the gas valve that is connected before the storage tank. Have a remedy of soapy water ready to ensure that you can put soapy water over the gas fittings to check for leakages. If you see bubbles then you have a leakage. Shut off the gas and fix the leak before you do anything else.

Step 13. After you have actually validated that there are no leakages you can currently switch on the gas and also light the pilot according to the producer’s guidelines. The guidelines on lighting the pilot are typically concealed on the front of the hot water heater. If you have trouble lighting the pilot you can call the helpline that is generally supplied on the front of the heating unit.

Step 14. Share a cool beverage of your selection with your pal that aided you out with your task, due to the fact that he deserves it, therefore, do you. This part is needed as well as not negotiable.

Enjoy your brand-new hot water heater and the complete satisfaction you have in doing it on your own.